产品概述
产品名称：塑料滑动摩擦磨损试验机（液晶显示）
型号：M-200
一、特点：
适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。制造标准：GB3960 塑料滑动摩擦磨损试验方法
二、主要适用范围及功能
本仪器是按照GB3960设计并制造。适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。本机采用16位单片机电子处理系统，使得本仪器各项测试指标精度非常高。由于集成程度很高，所以设备本身的稳定性*，本机具有一次设置，全自动运行，实验结束后自动停机，并检测摩损程度。是各个科研单位，大学，企业实验室的*检测设备。
三、功能特点：
1、试样尺寸： 30mm*7mm*6mm±0.1 mm
2、转动速度： 0-200转/分 连续可调
3、负 荷： 196N ± 0.2%（可扩充到392N）
4、摩擦环尺寸：￠40×10mm 倒角0.5×45°外圆表面与内圆同心度偏差小于0.01
5、摩擦力矩： 0--4N·m ±0.5%
6、计 数 器： 0-9999小时
7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。
四、精度：
1、速度精度：1%
2、负荷精度：0.5%
3、摩擦力矩精度：1%
4、计数器精度：1S
5、传感器测量精度：1% FS
五、 主要配置：
1、主机一台
2、高精度扭矩传感器一只
3、彩晶显示控制系统箱一台
4、4Kg砝码两件（备用一套）
5、标准磨擦环四件（备用两件）
6、台式微型打印机一台
7、产品使用说明书一份
8、产品合格证
9、产品装箱单一份
10、整机重量：约45公斤
六、主要技术规格：
1、zui大试验力： 2000N
2、试验力示值相对误差： 在满量程的10%以上，不超过±2%
3、试验力示值重复性相对误差：在满量程的10%以上，不超过2%
4、摩擦力矩测量范围： 0-15N.m
5、摩擦力矩示值相对误差： 在满量程的10%以上，不超过±3%
6、摩擦力矩示值重复性相对误差：在满量程的10%以上，不超过3%
7、下试样轴转速：400，200r/min 可选择（无级调速）
8、上试样轴转速：360，180r/min
9、上试样轴向zui大移动距离：±4mm
10、时间控制范围： 数显控制1s-9999min
1 1、转数控制范围： 数显控制 1-999999
1 2、曲线记录及数据处理：由HX计算机实现对各个参数的测量显示及数据处理，可时实显示时间-摩擦力矩等多种曲线
七、结构特征
该机由主机、电控箱、计算机测控系统组成。主机（附图a1）主要由铸造机座及位于机座左部的力矩测量部分，中部的下试样轴部分，右部的上试样轴部分、偏心轮轴部分和试验力施加与测量部分组成。
该机采用双速电动机（2880/1440转/分，1/0.75kW）驱动，电源为三相380V/50Hz，其接线及电气原理参照图c进行。
工作原理
上下试样轴的运转
双速电动机（1）通过三角皮带（2）齿轮（6）齿轮（7）齿轮（8）内齿轮（9）带动下试样轴（12），使其以200r/min（或400r/min）的转速转动；通过三角皮带（2）齿轮（6）齿轮（5）蜗杆轴（36）、滑动齿轮（39）和齿轮（40）的传递，使上试样轴（13）以180r/min（或360r/min）的转速转动。当上下试样轴都转动且两试样直径相等时，由于上下试样轴转速不等，（除滚动摩擦外），则在试样间带有10%的滑差率，使试样间具有滑动摩擦；改变试样直径，即可增大或减小滑差率，如要提高滑动速度，将滑动齿轮（39）移至右端与反向齿轮（17）啮合，使上试样轴（13）反向旋转即可。为了防止试验时固定螺母松动，下试样轴（12）上的螺纹是左旋的，而上试样轴（13）上的螺纹是右旋的。
上试样轴的固定
当做滑动摩擦试验时，为使上试样轴固定不动，应将滑动齿轮（39）移至中间位置，并用螺钉（38）固牢，齿轮（40）必须用销子（41）固定在摇摆头（37）上。
两试样间压力（试验力）的调整
试验力是通过弹簧（15）的压缩获得的，其增大或减小，可用螺母（19）进行调整，力值信号由传感器（18）送入电控箱并在计算机显示器上显示。
摩擦力矩的测量
摩擦力矩等于下试样半径与摩擦力的乘积，此力矩通过内齿轮（9）作用于齿轮（8）上，使摆架（4）及摆砣（3）产生偏转，由位移传感器（44）送入电控箱并在计算机显示器上显示。
下试样轴转数的测量
下试样轴转数通过转数传感器（11）测量并在计算机显示器上显示
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
型号：M-200
Model: M-200
一、特点：
One, characteristic:
适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
制造标准：GB3960 塑料滑动摩擦磨损试验方法
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
二、主要适用范围及功能
Two, the main scope and function
本仪器是按照GB3960设计并制造。适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。本机采用16位单片机电子处理系统，使得本仪器各项测试指标精度非常高。由于集成程度很高，所以设备本身的稳定性*，本机具有一次设置，全自动运行，实验结束后自动停机，并检测摩损程度。是各个科研单位，大学，企业实验室的*检测设备。
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
三、功能特点：
Three, function characteristics:
1、试样尺寸： 30mm*7mm*6mm±0.1 mm
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2、转动速度： 0-200转/分 连续可调
2, the rotation speed: 0-200 / continuously adjustable
3、负 荷： 196N ± 0.2%（可扩充到392N）
3, the load: 196N ± 0.2% （expandable to 392N）
4、摩擦环尺寸：￠40×10mm 倒角0.5×45°外圆表面与内圆同心度偏差小于0.01
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5、摩擦力矩： 0--4N·m ±0.5%
5, the friction torque: 0--4N m + 0.5%
6、计 数 器： 0-9999小时
6, counter: 0-9999 hours
7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
四、精度：
Four, accuracy:
1、速度精度：1%
1, speed accuracy: 1%
2、负荷精度：0.5%
2, load accuracy: 0.5%
3、摩擦力矩精度：1%
3, the friction torque accuracy: 1%
4、计数器精度：1S
4, the counter accuracy: 1S
5、传感器测量精度：1% FS
5, the sensor measurement accuracy: 1% FS
五、 主要配置：
Five, the main configuration:
1、主机一台
1, a host
2、高精度扭矩传感器一只
2, a high precision torque sensor
3、彩晶显示控制系统箱一台
3, color crystal display control system box
4、4Kg砝码两件（备用一套）
4, 4Kg weight two （alternate set）
5、标准磨擦环四件（备用两件）
5, the standard friction ring four （standby two）
6、台式微型打印机一台
6, a miniature printer
7、产品使用说明书一份
7, the instructions for use of products a
8、产品合格证
8, product certification
9、产品装箱单一份
9, product packing list
10、整机重量：约45公斤
10, weight: 45 kg
六、主要技术规格：
Six, the main technical specifications:
1、zui大试验力： 2000N
1, the maximum test force: 2000N
2、试验力示值相对误差： 在满量程的10%以上，不超过±2%
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
3、试验力示值重复性相对误差：在满量程的10%以上，不超过2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4、摩擦力矩测量范围： 0-15N.m
4, the friction torque measurement range: 0-15N.m
5、摩擦力矩示值相对误差： 在满量程的10%以上，不超过±3%
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6、摩擦力矩示值重复性相对误差：在满量程的10%以上，不超过3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7、下试样轴转速：400，200r/min 可选择（无级调速）
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8、上试样轴转速：360，180r/min
8, on the specimen axis speed: 360180r/min
9、上试样轴向zui大移动距离：±4mm
9, on the axis of the sample maximum moving distance: 4mm
10、时间控制范围： 数显控制1s-9999min
10, time control range: 1s-9999min digital control
1 1、转数控制范围： 数显控制 1-999999
11, speed control range: digital control 1-999999
1 2、曲线记录及数据处理：由HX计算机实现对各个参数的测量显示及数据处理，可时实显示时间-摩擦力矩等多种曲线
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
七、结构特征
Seven, structural characteristics
该机由主机、电控箱、计算机测控系统组成。主机（附图a1）主要由铸造机座及位于机座左部的力矩测量部分，中部的下试样轴部分，右部的上试样轴部分、偏心轮轴部分和试验力施加与测量部分组成。
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
该机采用双速电动机（2880/1440转/分，1/0.75kW）驱动，电源为三相380V/50Hz，其接线及电气原理参照图c进行。
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
工作原理
Working principle
上下试样轴的运转
On the specimen axis running
双速电动机（1）通过三角皮带（2）齿轮（6）齿轮（7）齿轮（8）内齿轮（9）带动下试样轴（12），使其以200r/min（或400r/min）的转速转动；通过三角皮带（2）齿轮（6）齿轮（5）蜗杆轴（36）、滑动齿轮（39）和齿轮（40）的传递，使上试样轴（13）以180r/min（或360r/min）的转速转动。当上下试样轴都转动且两试样直径相等时，由于上下试样轴转速不等，（除滚动摩擦外），则在试样间带有10%的滑差率，使试样间具有滑动摩擦；改变试样直径，即可增大或减小滑差率，如要提高滑动速度，将滑动齿轮（39）移至右端与反向齿轮（17）啮合，使上试样轴（13）反向旋转即可。为了防止试验时固定螺母松动，下试样轴（12）上的螺纹是左旋的，而上试样轴（13）上的螺纹是右旋的。
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
上试样轴的固定
Fixed on the specimen axis
当做滑动摩擦试验时，为使上试样轴固定不动，应将滑动齿轮（39）移至中间位置，并用螺钉（38）固牢，齿轮（40）必须用销子（41）固定在摇摆头（37）上。
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
两试样间压力（试验力）的调整
The presstation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
上试样轴的固定
Fixed on the specimen axis
当做滑动摩擦试验时，为使上试样轴固定不动，应将滑动齿轮（39）移至中间位置，并用螺钉（38）固牢，齿轮（40）必须用销子（41）固定在摇摆头（37）上。
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
两试样间压力（试验力）的调整
The pressure between the two specimen （test） adjustment
试验力是通过弹簧（15）的压缩获得的，其增大或减小，可用螺母（19）进行调整，力值信号由传感器（18）送入电控箱并在计算机显示器上显示。
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
摩擦力矩的测量
To measure the friction moment
摩擦力矩等于下试样半径与摩擦力的乘积，此力矩通过内齿轮（9）作用于齿轮（8）上，使摆架（4）及摆砣（3）产生偏转，由位移传感器（44）送入电控箱并在计算机显示器上显示。
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
下试样轴转数的测量
Measurement of the specimen under shaft revolution
下试样轴转数通过转数传感器（11）测量并在计算机显示器上显示
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
型号：M-200
Model: M-200
一、特点：
One, characteristic:
适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
制造标准：GB3960 塑料滑动摩擦磨损试验方法
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
二、主要适用范围及功能
Two, the main scope and function
本仪器是按照GB3960设计并制造。适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。本机采用16位单片机电子处理系统，使得本仪器各项测试指标精度非常高。由于集成程度很高，所以设备本身的稳定性*，本机具有一次设置，全自动运行，实验结束后自动停机，并检测摩损程度。是各个科研单位，大学，企业实验室的*检测设备。
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
三、功能特点：
Three, function characteristics:
1、试样尺寸： 30mm*7mm*6mm±0.1 mm
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2、转动速度： 0-200转/分 连续可调
2, the rotation speed: 0-200 / continuously adjustable
3、负 荷： 196N ± 0.2%（可扩充到392N）
3, the load: 196N ± 0.2% （expandable to 392N）
4、摩擦环尺寸：￠40×10mm 倒角0.5×45°外圆表面与内圆同心度偏差小于0.01
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5、摩擦力矩： 0--4N·m ±0.5%
5, the friction torque: 0--4N m + 0.5%
6、计 数 器： 0-9999小时
6, counter: 0-9999 hours
7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
四、精度：
Four, accuracy:
1、速度精度：1%
1, speed accuracy: 1%
2、负荷精度：0.5%
2, load accuracy: 0.5%
3、摩擦力矩精度：1%
3, the friction torque accuracy: 1%
4、计数器精度：1S
4, the counter accuracy: 1S
5、传感器测量精度：1% FS
5, the sensor measurement accuracy: 1% FS
五、 主要配置：
Five, the main configuration:
1、主机一台
1, a host
2、高精度扭矩传感器一只
2, a high precision torque sensor
3、彩晶显示控制系统箱一台
3, color crystal display control system box
4、4Kg砝码两件（备用一套）
4, 4Kg weight two （alternate set）
5、标准磨擦环四件（备用两件）
5, the standard friction ring four （standby two）
6、台式微型打印机一台
6, a miniature printer
7、产品使用说明书一份
7, the instructions for use of products a
8、产品合格证
8, product certification
9、产品装箱单一份
9, product packing list
10、整机重量：约45公斤
10, weight: 45 kg
六、主要技术规格：
Six, the main technical specifications:
1、zui大试验力： 2000N
1, the maximum test force: 2000N
2、试验力示值相对误差： 在满量程的10%以上，不超过±2%
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
3、试验力示值重复性相对误差：在满量程的10%以上，不超过2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4、摩擦力矩测量范围： 0-15N.m
4, the friction torque measurement range: 0-15N.m
5、摩擦力矩示值相对误差： 在满量程的10%以上，不超过±3%
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6、摩擦力矩示值重复性相对误差：在满量程的10%以上，不超过3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7、下试样轴转速：400，200r/min 可选择（无级调速）
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8、上试样轴转速：360，180r/min
8, on the specimen axis speed: 360180r/min
9、上试样轴向zui大移动距离：±4mm
9, on the axis of the sample maximum moving distance: 4mm
10、时间控制范围： 数显控制1s-9999min
10, time control range: 1s-9999min digital control
1 1、转数控制范围： 数显控制 1-999999
11, speed control range: digital control 1-999999
1 2、曲线记录及数据处理：由HX计算机实现对各个参数的测量显示及数据处理，可时实显示时间-摩擦力矩等多种曲线
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
七、结构特征
Seven, structural characteristics
该机由主机、电控箱、计算机测控系统组成。主机（附图a1）主要由铸造机座及位于机座左部的力矩测量部分，中部的下试样轴部分，右部的上试样轴部分、偏心轮轴部分和试验力施加与测量部分组成。
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
该机采用双速电动机（2880/1440转/分，1/0.75kW）驱动，电源为三相380V/50Hz，其接线及电气原理参照图c进行。
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
工作原理
Working principle
上下试样轴的运转
On the specimen axis running
双速电动机（1）通过三角皮带（2）齿轮（6）齿轮（7）齿轮（8）内齿轮（9）带动下试样轴（12），使其以200r/min（或400r/min）的转速转动；通过三角皮带（2）齿轮（6）齿轮（5）蜗杆轴（36）、滑动齿轮（39）和齿轮（40）的传递，使上试样轴（13）以180r/min（或360r/min）的转速转动。当上下试样轴都转动且两试样直径相等时，由于上下试样轴转速不等，（除滚动摩擦外），则在试样间带有10%的滑差率，使试样间具有滑动摩擦；改变试样直径，即可增大或减小滑差率，如要提高滑动速度，将滑动齿轮（39）移至右端与反向齿轮（17）啮合，使上试样轴（13）反向旋转即可。为了防止试验时固定螺母松动，下试样轴（12）上的螺纹是左旋的，而上试样轴（13）上的螺纹是右旋的。
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
上试样轴的固定
Fixed on the specimen axis
当做滑动摩擦试验时，为使上试样轴固定不动，应将滑动齿轮（39）移至中间位置，并用螺钉（38）固牢，齿轮（40）必须用销子（41）固定在摇摆头（37）上。
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
两试样间压力（试验力）的调整
The pressure between the two specimen （test） adjustment
试验力是通过弹簧（15）的压缩获得的，其增大或减小，可用螺母（19）进行调整，力值信号由传感器（18）送入电控箱并在计算机显示器上显示。
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
摩擦力矩的测量
To measure the friction moment
摩擦力矩等于下试样半径与摩擦力的乘积，此力矩通过内齿轮（9）作用于齿轮（8）上，使摆架（4）及摆砣（3）产生偏转，由位移传感器（44）送入电控箱并在计算机显示器上显示。
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
下试样轴转数的测量
Measurement of the specimen under shaft revolution
下试样轴转数通过转数传感器（11）测量并在计算机显示器上显示
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
型号：M-200
Model: M-200
一、特点：
One, characteristic:
适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
制造标准：GB3960 塑料滑动摩擦磨损试验方法
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
二、主要适用范围及功能
Two, the main scope and function
本仪器是按照GB3960设计并制造。适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。本机采用16位单片机电子处理系统，使得本仪器各项测试指标精度非常高。由于集成程度很高，所以设备本身的稳定性*，本机具有一次设置，全自动运行，实验结束后自动停机，并检测摩损程度。是各个科研单位，大学，企业实验室的*检测设备。
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
三、功能特点：
Three, function characteristics:
1、试样尺寸： 30mm*7mm*6mm±0.1 mm
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2、转动速度： 0-200转/分 连续可调
2, the rotation speed: 0-200 / continuously adjustable
3、负 荷： 196N ± 0.2%（可扩充到392N）
3, the load: 196N ± 0.2% （expandable to 392N）
4、摩擦环尺寸：￠40×10mm 倒角0.5×45°外圆表面与内圆同心度偏差小于0.01
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5、摩擦力矩： 0--4N·m ±0.5%
5, the friction torque: 0--4N m + 0.5%
6、计 数 器： 0-9999小时
6, counter: 0-9999 hours
7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
四、精度：
Four, accuracy:
1、速度精度：1%
1, speed accuracy: 1%
2、负荷精度：0.5%
2, load accuracy: 0.5%
3、摩擦力矩精度：1%
3, the friction torque accuracy: 1%
4、计数器精度：1S
4, the counter accuracy: 1S
5、传感器测量精度：1% FS
5, the sensor measurement accuracy: 1% FS
五、 主要配置：
Five, the main configuration:
1、主机一台
1, a host
2、高精度扭矩传感器一只
2, a high precision torque sensor
3、彩晶显示控制系统箱一台
3, color crystal display control system box
4、4Kg砝码两件（备用一套）
4, 4Kg weight two （alternate set）
5、标准磨擦环四件（备用两件）
5, the standard friction ring four （standby two）
6、台式微型打印机一台
6, a miniature printer
7、产品使用说明书一份
7, the instructions for use of products a
8、产品合格证
8, product certification
9、产品装箱单一份
9, product packing list
10、整机重量：约45公斤
10, weight: 45 kg
六、主要技术规格：
Six, the main technical specifications:
1、zui大试验力： 2000N
1, the maximum test force: 2000N
2、试验力示值相对误差： 在满量程的10%以上，不超过±2%
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
3、试验力示值重复性相对误差：在满量程的10%以上，不超过2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4、摩擦力矩测量范围： 0-15N.m
4, the friction torque measurement range: 0-15N.m
5、摩擦力矩示值相对误差： 在满量程的10%以上，不超过±3%
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6、摩擦力矩示值重复性相对误差：在满量程的10%以上，不超过3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7、下试样轴转速：400，200r/min 可选择（无级调速）
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8、上试样轴转速：360，180r/min
8, on the specimen axis speed: 360180r/min
9、上试样轴向zui大移动距离：±4mm
9, on the axis of the sample maximum moving distance: 4mm
10、时间控制范围： 数显控制1s-9999min
10, time control range: 1s-9999min digital control
1 1、转数控制范围： 数显控制 1-999999
11, speed control range: digital control 1-999999
1 2、曲线记录及数据处理：由HX计算机实现对各个参数的测量显示及数据处理，可时实显示时间-摩擦力矩等多种曲线
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
七、结构特征
Seven, structural characteristics
该机由主机、电控箱、计算机测控系统组成。主机（附图a1）主要由铸造机座及位于机座左部的力矩测量部分，中部的下试样轴部分，右部的上试样轴部分、偏心轮轴部分和试验力施加与测量部分组成。
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
该机采用双速电动机（2880/1440转/分，1/0.75kW）驱动，电源为三相380V/50Hz，其接线及电气原理参照图c进行。
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
工作原理
Working principle
上下试样轴的运转
On the specimen axis running
双速电动机（1）通过三角皮带（2）齿轮（6）齿轮（7）齿轮（8）内齿轮（9）带动下试样轴（12），使其以200r/min（或400r/min）的转速转动；通过三角皮带（2）齿轮（6）齿轮（5）蜗杆轴（36）、滑动齿轮（39）和齿轮（40）的传递，使上试样轴（13）以180r/min（或360r/min）的转速转动。当上下试样轴都转动且两试样直径相等时，由于上下试样轴转速不等，（除滚动摩擦外），则在试样间带有10%的滑差率，使试样间具有滑动摩擦；改变试样直径，即可增大或减小滑差率，如要提高滑动速度，将滑动齿轮（39）移至右端与反向齿轮（17）啮合，使上试样轴（13）反向旋转即可。为了防止试验时固定螺母松动，下试样轴（12）上的螺纹是左旋的，而上试样轴（13）上的螺纹是右旋的。
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
上试样轴的固定
Fixed on the specimen axis
当做滑动摩擦试验时，为使上试样轴固定不动，应将滑动齿轮（39）移至中间位置，并用螺钉（38）固牢，齿轮（40）必须用销子（41）固定在摇摆头（37）上。
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
两试样间压力（试验力）的调整
The pressure between the two specimen （test） adjustment
试验力是通过弹簧（15）的压缩获得的，其增大或减小，可用螺母（19）进行调整，力值信号由传感器（18）送入电控箱并在计算机显示器上显示。
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
摩擦力矩的测量
To measure the friction moment
摩擦力矩等于下试样半径与摩擦力的乘积，此力矩通过内齿轮（9）作用于齿轮（8）上，使摆架（4）及摆砣（3）产生偏转，由位移传感器（44）送入电控箱并在计算机显示器上显示。
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
下试样轴转数的测量
Measurement of the specimen under shaft revolution
下试样轴转数通过转数传感器（11）测量并在计算机显示器上显示
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
型号：M-200
Model: M-200
一、特点：
One, characteristic:
适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
制造标准：GB3960 塑料滑动摩擦磨损试验方法
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
二、主要适用范围及功能
Two, the main scope and function
本仪器是按照GB3960设计并制造。适用于塑料制品及橡胶制品或其他复合材料的滑动摩擦，摩损性能测试。也可对试验中试样的摩擦力、摩擦系数和摩损量进行测定。本机采用16位单片机电子处理系统，使得本仪器各项测试指标精度非常高。由于集成程度很高，所以设备本身的稳定性*，本机具有一次设置，全自动运行，实验结束后自动停机，并检测摩损程度。是各个科研单位，大学，企业实验室的*检测设备。
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
三、功能特点：
Three, function characteristics:
1、试样尺寸： 30mm*7mm*6mm±0.1 mm
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2、转动速度： 0-200转/分 连续可调
2, the rotation speed: 0-200 / continuously adjustable
3、负 荷： 196N ± 0.2%（可扩充到392N）
3, the load: 196N ± 0.2% （expandable to 392N）
4、摩擦环尺寸：￠40×10mm 倒角0.5×45°外圆表面与内圆同心度偏差小于0.01
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5、摩擦力矩： 0--4N·m ±0.5%
5, the friction torque: 0--4N m + 0.5%
6、计 数 器： 0-9999小时
6, counter: 0-9999 hours
7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
四、精度：
Four, accuracy:
1、速度精度：1%
1, speed accuracy: 1%
2、负荷精度：0.5%
2, load accuracy: 0.5%
3、摩擦力矩精度：1%
3, the friction torque accuracy: 1%
4、计数器精度：1S
4, the counter accuracy: 1S
5、传感器测量精度：1% FS
5, the sensor measurement accuracy: 1% FS
五、 主要配置：
Five, the main configuration:
1、主机一台
1, a host
2、高精度扭矩传感器一只
2, a high precision torque sensor
3、彩晶显示控制系统箱一台
3, color crystal display control system box
4、4Kg砝码两件（备用一套）
4, 4Kg weight two （alternate set）
5、标准磨擦环四件（备用两件）
5, the standard friction ring four （standby two）
6、台式微型打印机一台
6, a miniature printer
7、产品使用说明书一份
7, the instructions for use of products a
8、产品合格证
8, product certification
9、产品装箱单一份
9, product packing list
10、整机重量：约45公斤
10, weight: 45 kg
六、主要技术规格：
Six, the main technical specifications:
1、zui大试验力： 2000N
1, the maximum test force: 2000N
2、试验力示值相对误差： 在满量程的10%以上，不超过±2%
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
3、试验力示值重复性相对误差：在满量程的10%以上，不超过2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4、摩擦力矩测量范围： 0-15N.m
4, the friction torque measurement range: 0-15N.m
5、摩擦力矩示值相对误差： 在满量程的10%以上，不超过±3%
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6、摩擦力矩示值重复性相对误差：在满量程的10%以上，不超过3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7、下试样轴转速：400，200r/min 可选择（无级调速）
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8、上试样轴转速：360，180r/min
8, on the specimen axis speed: 360180r/min
9、上试样轴向zui大移动距离：±4mm
9, on the axis of the sample maximum moving distance: 4mm
10、时间控制范围： 数显控制1s-9999min
10, time control range: 1s-9999min digital control
1 1、转数控制范围： 数显控制 1-999999
11, speed control range: digital control 1-999999
1 2、曲线记录及数据处理：由HX计算机实现对各个参数的测量显示及数据处理，可时实显示时间-摩擦力矩等多种曲线
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
七、结构特征
Seven, structural characteristics
该机由主机、电控箱、计算机测控系统组成。主机（附图a1）主要由铸造机座及位于机座左部的力矩测量部分，中部的下试样轴部分，右部的上试样轴部分、偏心轮轴部分和试验力施加与测量部分组成。
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
该机采用双速电动机（2880/1440转/分，1/0.75kW）驱动，电源为三相380V/50Hz，其接线及电气原理参照图c进行。
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
工作原理
Working principle
上下试样轴的运转
On the specimen axis running
双速电动机（1）通过三角皮带（2）齿轮（6）齿轮（7）齿轮（8）内齿轮（9）带动下试样轴（12），使其以200r/min（或400r/min）的转速转动；通过三角皮带（2）齿轮（6）齿轮（5）蜗杆轴（36）、滑动齿轮（39）和齿轮（40）的传递，使上试样轴（13）以180r/min（或360r/min）的转速转动。当上下试样轴都转动且两试样直径相等时，由于上下试样轴转速不等，（除滚动摩擦外），则在试样间带有10%的滑差率，使试样间具有滑动摩擦；改变试样直径，即可增大或减小滑差率，如要提高滑动速度，将滑动齿轮（39）移至右端与反向齿轮（17）啮合，使上试样轴（13）反向旋转即可。为了防止试验时固定螺母松动，下试样轴（12）上的螺纹是左旋的，而上试样轴（13）上的螺纹是右旋的。
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error o
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range5N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen nction
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data ment part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
Product Name: friction and wear testing machine plastic sliding （liquid crystal display）
Model: M-200
One, characteristic:
Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination.
Manufacturing standards: Test Method for friction and wear of GB3960 plastic sliding
Two, the main scope and function
The apparatus is in accordance with the GB3960 design and manufacturing. Sliding friction is applied to the plastic products and rubber products or other composite materials, friction performance test. Can also be used to test the friction test, friction coefficient and wear volume determination. This machine adopts 16 bit single chip electronic processing system, the instrument and the test precision is very high. Due to the integrated degree is very high, so the stability of the equipment itself, the machine has a set, automatic operation, automatic stop after the end of the experiment, and detect the abrasion degree. Is the scientific research unit, University, necessary testing equipment enterprise laboratory.
Three, function characteristics:
1, the sample size: 30mm*7mm*6mm ± 0.1 mm
2, the rotation speed: 0-200 / continuously adjustable
3, the load: 196N ± 0.2% （expandable to 392N）
4, the friction ring size: 40 x 10mm ￠ chamfer 0.5 × 45 ° surface of the outer circle and inner circle concentricity deviation is less than 0.01
5, the friction torque: 0--4N m + 0.5%
6, counter: 0-9999 hours
7, weight: 4KG weight a, 1KG weight 4, weight function can be realized.
Four, accuracy:
1, speed accuracy: 1%
2, load accuracy: 0.5%
3, the friction torque accuracy: 1%
4, the counter accuracy: 1S
5, the sensor measurement accuracy: 1% FS
Five, the main configuration:
1, a host
2, a high precision torque sensor
3, color crystal display control system box
4, 4Kg weight two （alternate set）
5, the standard friction ring four （standby two）
6, a miniature printer
7, the instructions for use of products a
8, product certification
9, product packing list
10, weight: 45 kg
Six, the main technical specifications:
1, the maximum test force: 2000N
2, the test force relative error of indication: over 10% of full scale, not more than ± 2%
Indication repeatability relative error of 3, test force: over 10% of full scale, not exceeding 2%
4, the friction torque measurement range: 0-15N.m
5, the friction moment relative error of indication: over 10% of full scale, not more than ± 3%
6, the value of friction torque repeatability relative error: over 10% of full scale, not exceeding 3%
7, the specimen under shaft speed: 400200r/min can choose （stepless）
8, on the specimen axis speed: 360180r/min
9, on the axis of the sample maximum moving distance: 4mm
10, time control range: 1s-9999min digital control
11, speed control range: digital control 1-999999
12, the curve recording and data processing: by HX special computer realize the measurement of the parameters of the display and the data processing, real time display - friction torque and so on many kinds of curves can be.
Seven, structural characteristics
The machine is composed of computer control system, electric control box, host. The host （Figure A1） is mainly composed of cast frame and torque measurement part is positioned on the frame of the specimen axis part of left, middle, right on the part of sample axis, eccentric shaft part and the test force composition and measuring part.
The machine adopts double speed motor （2880/1440 R / min, 1/0.75kW） drive, power supply for three-phase 380V/50Hz, the connection and the electrical principle refer to figure C.
Working principle
On the specimen axis running
Double speed motor （1） through the triangle belt （2） （6） gear gear gear （7） （8） （9） the internal gear drive shaft （12 samples）, the 200r/min （or 400r/min） of the speed of rotation; through the triangle belt （2） gear （6） （5） of worm gear shaft （36）, （39） sliding gear and gear （40） transfer, make the specimen axis （13） to 180r/min （or 360r/min） of the speed of rotation. When the upper and the lower shaft to rotate and sample specimen diameter is equal to two, since the upper and lower sample shaft speed range, （with the exception of rolling friction outside）, with a slip of 10% in the sample, the sample with sliding friction between; change the specimen diameter, can increase or decrease the slip ratio, such as to make high sliding speed, sliding gear （39） moved to the right side and the reverse gear （17） meshing, the specimen axis （13） reverse rotation can be. In order to prevent the test specimen under fixed nut is loose, the shaft （12） on the thread is left-handed, and the specimen axis （13） on the threads are right-handed.
Fixed on the specimen axis
As the sliding friction tests on samples, in order to make the shaft is fixed, the sliding gear （39） intermediate position to, and the use of screws （38） fixed, gear （40） must use the pin （41） is fixed on the swing head （37）.
The pressure between the two specimen （test） adjustment
Test force by spring （15） compression is obtained, its increase or decrease, the nut （19） can be adjusted, force signal from the sensor （18） into the electric control box is displayed on a computer monitor.
To measure the friction moment
The friction torque is equal to the product of sample radius and friction, the torque through the internal gear （9） acting on the gear （8）, the swinging rack （4） and weight （3） generated by the deflection, the displacement sensor （44） into the electric control box is displayed on a computer monitor.
Measurement of the specimen under shaft revolution
The specimen under shaft revolution through speed sensor （11） measured and displayed on a computer monitor
- 上一个： 熔融指数仪 厂家
- 下一个： 液体增塑剂电阻率测定仪，微电流测定仪
